Electric scooter motor overheating: when it's normal, and when you should be concerned
A scooter motor will always get a little warm: this is the price you pay for the power it delivers. After a long uphill climb or a series of accelerations, a motor bell that is warm to the touch is not necessarily abnormal. What should be concerning is excessive heat that appears under conditions where it didn't exist before, and is accompanied by a smell, noises, or a loss of power, or if it only affects one of the two motors. This guide will help you distinguish between normal operation and potential problems, and help you identify the cause.
The essentials
- The heat primarily comes from the current flowing through the motor windings: the more force the motor exerts, the hotter it gets, and the temperature increase is significantly faster than the current increase.
- Normal heating follows exertion: inclines, heavy loads, repeated accelerations. Abnormal heating appears without a clear reason or has changed recently.
- Simply touching the bell (housing) is not enough to judge the temperature: the inside of the motor is hotter than the outside.
- Abnormal overheating is often caused by factors other than the motor itself: settings, a brake that is rubbing, an underinflated tire, or a faulty sensor or phase.
Why does a motor overheat?
An electric motor converts electrical energy into motion with a very good efficiency, but not a perfect one. The energy lost becomes heat, especially in the copper windings, where it increases with the square of the current: doubling the current multiplies this heat by approximately four. That's why a motor that is forced to work at low speed, uphill, or when starting a heavy machine, gets much hotter than a motor that is running at a constant speed on a flat surface. Our guide on electric motor overheating details these losses and what the heat threatens: the insulating varnish of the windings and the magnets, which lose their strength if they get too hot.
In addition to its other drawbacks, a scooter hub motor has a further limitation: it's enclosed in a waterproof housing that sits close to the ground, and it primarily dissipates heat through the air that flows around it. At low speeds, this airflow is slow.
Normal or abnormal heating: key indicators
| Situation: | Quite normal | Rather abnormal |
|---|---|---|
| After a long uphill climb or when the vehicle is heavily loaded.. | Smooth throttle response, stable power delivery | Power loss, smell of varnish |
| On a flat surface, for a relaxed ride | Warm motor | Motor overheating |
| On a dual-motor scooter | The two are at approximately the same temperature | One motor is noticeably hotter than the other |
| Since a setting change or controller update.. | Slight increase if the current has been increased | Significant heating, even with minimal effort |
| With noises or jerks | Never | Electrical or mechanical fault |
The feel can be misleading: the outer casing might seem bearable, while the windings inside are much hotter. If your motor has a temperature sensor and your controller or display reads it, rely on that reading rather than your hand. And touch with caution: the bell or brake disc can get extremely hot.
Causes of abnormal overheating
An overly aggressive setting
On an adjustable controller, increasing the motor current increases the power output, but also significantly increases the heat. "Defluxing," which allows the motor to exceed its natural speed, also consumes current without producing torque, and generates heat. After a controller change or adjustment, this can often be the cause of increased heat.
An engine that is not properly matched to the vehicle
A high-speed motor on a heavy machine, used in the city or on hills, often operates at high current and low speed, which is its operating temperature range. Our guide High Speed or High Torque explains how to choose the right motor winding based on the intended use.
Something is hindering the wheel's rotation
A brake that rubs, a worn bearing, or an underinflated tire force the motor to work constantly. With the wheel raised and the motor disconnected, the wheel should rotate freely and for a long time.
A faulty sensor or phase
If a Hall sensor provides incorrect information, the current arrives at the wrong time: one part pushes, another part brakes, and everything turns into heat. A poorly connected phase forces the other two to carry the entire load. In both cases, the motor overheats, makes a groaning noise, and lacks power. Our guide on how to test a scooter motor with a multimeter shows you how to check it.
A motor detection failure
On controllers that measure the motor directly, a detection performed under poor conditions can result in incorrect parameters. The motor will run, but with reduced efficiency. Re-running the detection, with the wheel raised and the battery fully charged, often corrects the problem.
What to do when the motor is overheating
- In the moment: Reduce the effort; ride at a moderate speed on flat surfaces rather than stopping on an incline. Movement allows air to circulate around the motor.
- After the ride: Allow to cool down in open air. Never pour water on a hot motor to cool it down: the thermal shock and the water drawn into the motor as it cools are more dangerous than the heat itself.
- If the power decreases while riding: This is often due to the thermal protection of the controller activating. It's there to protect the motor; do not disable it.
- If you smell burning varnish: stop immediately. The insulation of the windings may have been damaged, and a short circuit between the windings could occur.
Reduce overheating permanently
Here are the solutions, from the simplest to the most complex: adjust tire pressure and friction, revert to reasonable current settings, improve heat dissipation, and finally, if the application requires it, switch to a larger or more suitable motor. A larger motor has more copper and more surface area, so it generates less heat for the same amount of power; see our electric scooter motors.
Workshop tip
For motors that work hard, whether going uphill, under load, or on a track, proper ventilation makes a significant difference. Our motor ventilation systems with six blades are mounted on the motor shaft, on the cable side, for our MHS, MHT, XHS, and XHT motors to improve their cooling. When combined with appropriate settings, this is often the most effective solution before considering a motor replacement.
Frequently Asked Questions
Only one of my two motors is getting hot, why is that?
The two motors are not operating in the same way: there are different settings between the two controllers, the brake is rubbing on one side, a bearing is worn, or there is a faulty sensor or phase on the "hot" motor. First, compare the free rotation of both wheels.
My motor gets very hot in the city, but not when I'm riding on the open road. Is this normal?
Yes, to some extent. In urban environments, frequent stops and starts require a significant amount of current at low speeds, with limited airflow for cooling. A motor winding optimized for torque or gentler settings can reduce this effect.
Can heat permanently damage a motor?
Yes: Beyond their limitations, the varnish coating on the windings degrades, and the magnets can lose some of their strength irreversibly. The motor then becomes less powerful and heats up even more.
Should you put ferrofluid in a motor wheel?
This is a solution used to better transfer heat from the windings to the bell, but it has its limitations. Our guide on ferrofluid details its advantages and limitations.